Content | Universal Effects Pedal Floor Board with Integrated Power Supply
Ultra-compact and lightweight pedal board for transporting up to 12 effects pedals
Generous 1.7 A power adapter included for powering more than 12 devices*—includes all cabling
Ultra-rigid plastic design withstands even heavy impact
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany
Love your pedal chain? Rather than tossing your effects and their individual power adapters into a duffel bag after a gig, keep them safe—and ready to rock at a moment's notice—with the PB1000.
It's all about connections
This pedal board makes hooking up 12 2.5" x 4.5" pedals as easy as hooking up just one (of course, if you're using pedals that aren't 2.5" x 4.5“, the snug foam padding can be cut to accommodate pedals of varying shapes). The PB1000 includes ¼" patch cables, so you can leave your pedals connected to one another, ready to pass signal even when you're transporting them. It also comes with 1 x 12 daisy chain cabling so that when you plug in the 1.7 A power adapter, all your pedals receive power.
The Ins and Outs
Connect your guitar, bass or keyboard to the single ¼" input in the upper right corner of the board. A pair of ¼" FROM EFFECTS jacks in the upper left corner allow you to connect stereo effects, and two ¼" OUTPUT TO AMP jacks send a left and right stereo signal to up to two amps. When it is time to load out, just unplug the power supply, disconnect your guitar and amp, put the lid back on the PB1000 and slide the locking latches back into place. The heavy-impact plastic casing will protect your pedals from the rigors of the road.
Value
You have invested considerable time and money into your effects chain. Keep it safe and sounding great with the PB1000. Check it out at your nearest BEHRINGER dealer.
User's Manual |
FOR X-S, Xio, all ReMOTEs, Bass St. KB/Rack, D-. A-, K-St
| 9 Volts - 670 mA - TC Approved Power
The new PowerPlug 9 PSU is the perfect add on accessory
sale for most TC Electronic guitar FX pedals (TonePrint,
PolyTune, Ditto Loopers and analog drive pedals.
For TC-Helicon DC powered devices and TC Electronic Nova pedals please chose PowerPlug 12 instead. |
Product Features: - 1.7 A current capacity can power more than 20 effects pedals, keyboards and other DC 9 V gear*
- Supplied with a full complement of connectors and jumper cords for total compatibility
- Includes 4 assorted jumper cables and 2 daisy-chain cables each with 5 connectors
- Takes up only one outlet space and frees up more room for your pedals
- Runs on any AC power supply from 100 - 240 V; worldwide usability without transformer
- Transformerless design eliminates 50/60-cycle hum and extraneous noise
- High-quality components and exceptionally rugged construction ensure long life
|
- Choice of 9V DC, 12V DC, 12V AC or 18VDC -150mA
- Noise-cancelling galvanic isolated outputs
- Traditional EI Transformer
- Several different voltage types served
- Current doubler = the possibility of as much as 600 mA
- Switchable 115V or 230V
- Compact, rugged, road-ready design
| User\'s manual
Palmer MI PWT 12 MK 2
Universal 12-Outlet Pedalboard Power Supply
- Fully regulated universal pedalboard power supply
- 12 standard centre negative outlets with 2,000 mA output total
- 8 x 9 V outlets (300 mA each)
- 4 variable voltage outlets 6 to 18 V (500 mA each)
- Short circuit and overload protection for each outlet
- DC cables and mains adapter included
The PWT 12 is a heavy duty (2000 mA) universal pedal board power supply with 12 isolated 9 V DC, centre-negative female pin-connector outputs. Four of the outputs feature adjustable voltage from 6 to 18 volts. The variable outputs enable the simulation of voltage drop or \'battery sag\' in old batteries. The power supply is regulated for constant voltage supply and protected against short circuit and overloading. The PWT 12 is equipped with a power LED and a two-colour LED output status indicator. It is supplied with an AC adapter and a set of DC cables. The PWT 12 is the ideal solution for power-hungry foot pedals or 9-volt effects units that can be operated at higher voltages for increased dynamics and stability.
Product type
Power Supplies
Input voltage
100 - 250 V
Outputs
12
Output connectors
2.1 x 5.5 mm
Output voltage
12 V , 18 V , 9 V
Max. output current
2000 mA
Isolated outputs
yes
Polarity
center negative
Cord length
25 - 50 cm
Indicators
fault , Power
Controls
Output voltage selector
Width
193 mm
Depth
70 mm
Height
30 mm
Weight
0,4 kg
|
Reviews
There are no reviews yet.